Easy Steps to Change your IP in less than a minute,,,!!! 13:14 Rahul No comments Email This BlogThis! Share to Twitter Share to Facebook Here is the 10 most easy quick step method to change the IP address by changing the properties in LAN (Local Area Netwok). Step 1: Click on "Start"---> "Run" Then Type in "command" or "cmd" and hit OK or press ENTER. Step 2: In the Command Prompt also known as "MS-DOS" prompt just type "ipconfig /release" & Hit Enter. Type "exit" and leave the prompt Step3 : Right-click on "Network Places" or "My Network Places" ---> Click on "properties" .Then Right click on "Local Area Connection"--->Click "properties" Step 4: Now click on the "Internet Protocol (TCP/IP)" from the list under the "General" tab Step 5: Click on "Use the following IP address" under the "General" tab BINGOOO,,,,!!! Now you can type in your own IP address . Step 6: Now Press "Tab" and it should automatically fill in the "Subnet Mask" section with default numbers. Step 7: Hit the "Ok" button twice and you are now back to the "Local Area Connection" screen. Step 8: Now Right-click back on "Local Area Connection" and go to properties again. Step 9: Go back to the "TCP/IP" settings Now , Select "Obtain an IP address automatically" Step 10: Hit "Ok" twice again BANG BANG BANG,,,,,!!!! :D ;) You now have a new IP address However it only changes your dynamic IP address and not not your ISP/IP address. Hope you enjoyed this post,,,!!! Cheers,,,!!! ;)
By
jesica
- we say welcome to the blog Tecno Android Phones we provide a lot of latest gadget information that must be very dear for you to miss, now we will discuss first about
we have collected a lot of information to make this article to complete for you, Please read:
Articles :
full Link :
Articles :
full Link :
You can also see our article on:
Easy Steps to Change your IP in less than a minute,,,!!! 13:14 Rahul No comments Email This BlogThis! Share to Twitter Share to Facebook Here is the 10 most easy quick step method to change the IP address by changing the properties in LAN (Local Area Netwok). Step 1: Click on "Start"---> "Run" Then Type in "command" or "cmd" and hit OK or press ENTER. Step 2: In the Command Prompt also known as "MS-DOS" prompt just type "ipconfig /release" & Hit Enter. Type "exit" and leave the prompt Step3 : Right-click on "Network Places" or "My Network Places" ---> Click on "properties" .Then Right click on "Local Area Connection"--->Click "properties" Step 4: Now click on the "Internet Protocol (TCP/IP)" from the list under the "General" tab Step 5: Click on "Use the following IP address" under the "General" tab BINGOOO,,,,!!! Now you can type in your own IP address . Step 6: Now Press "Tab" and it should automatically fill in the "Subnet Mask" section with default numbers. Step 7: Hit the "Ok" button twice and you are now back to the "Local Area Connection" screen. Step 8: Now Right-click back on "Local Area Connection" and go to properties again. Step 9: Go back to the "TCP/IP" settings Now , Select "Obtain an IP address automatically" Step 10: Hit "Ok" twice again BANG BANG BANG,,,,,!!!! :D ;) You now have a new IP address However it only changes your dynamic IP address and not not your ISP/IP address. Hope you enjoyed this post,,,!!! Cheers,,,!!! ;)
Articles about finished discussed
We think it is enough information about
, hopefully the information we give can give benefit for you,
If you feel the information that we provide can provide benefits for others please share with link https://southernmatron.blogspot.com/2012/12/click-properties-step-4-now-click-on.html thank you for visiting our blog page and do not forget to visit other pages.
Tag :
Tags :
Subscribe to:
Post Comments (Atom)
0 komentar:
Post a Comment